PCjs Machines
Home of the original IBM PC emulator for browsers.
DEC VT100 ROMs
8080 Firmware (8Kb)
The DEC VT100 Terminal used four 2Kb ROMs to store all the firmware used by the 8080 processor. The combined contents of those ROMs have been stored as an 8Kb JSON image in VT100.
As Trammell Hudson’s VT100 Page explains:
There are four 8316E ROM chips for the 8080 CPU on the logic board. Since they are custom mask ROMs, Digital was able to have a different chip-select bit pattern and avoided having separate NOT gates on the inputs. Note that the schematic appears to be incorrect – E56 is the low order, and E40 is the high order address bits.
He then describes the memory map as follows:
ROM chip CS1 (20) A11/CS2 (18) A12/CS3 (21) Mapped address
E40 H H H 0x1800
E45 H L H 0x1000
E52 H H L 0x0800
E56 H L L 0x0000
The above PCB chip locations correspond to the following DEC ROMs:
- E56: 23-061E2.bin
- E52: 23-032E2.bin
- E45: 23-033E2.bin
- E40: 23-034E2.bin
And sure enough, concatenating those four DEC ROMs:
cat 23-061E2.bin 23-032E2.bin 23-033E2.bin 23-034E2.bin > VT100.bin
produces a perfect match for Trammell Hudson’s VT100.bin.
Character Generator (2Kb)
The VT100 also used one 2Kb character generator ROM, which is stored in 23-018E2. The ROM contains 128 rows of character data, 16 bytes per character. Only 10 of each of the 16 bytes are used.
To understand the format of the character data, let’s take a look at the data for the letter “A”, which has an ASCII code of 65 (0x41). That means the data for “A” should start at offset 0x41 * 0x10, or 0x410. Here’s the corresponding line from 23-018E2:
0x10,0x28,0x44,0x82,0xFE,0x82,0x82,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // 0x00000410 .(D.............
and if we display the data as bits instead of bytes:
. . . 1 . . . . // 0x10
. . 1 . 1 . . . // 0x28
. 1 . . . 1 . . // 0x44
1 . . . . . 1 . // 0x82
1 1 1 1 1 1 1 . // 0xFE
1 . . . . . 1 . // 0x82
1 . . . . . 1 . // 0x82
. . . . . . . . // 0x00
. . . . . . . . // 0x00
. . . . . . . . // 0x00
it should be clear how the shape of the character is defined. However, the character generator ROM doesn’t tell the whole story, because the VT100’s display circuitry has a few additional tricks up its sleeve.
Since the ROM contains only 8 bits of data for each character row, and character cells are effectively 10x10 (or 9x10 in 132-column mode), there is a natural gap between adjacent characters. However, when horizontal line-drawing characters are used, the VT100 wants those characters to seamlessly connect with one another, so if the final bit in any row of character data is set, the VT100 will “replicate” that bit across the rest of cell.
As page 4-52 of DEC’s VT100 Technical Manual (July 1982) explains:
Data, coming either from the screen RAM for scan 1 or the line buffer for scans 2 through 10, becomes part of an address to a character generator ROM. (See Figure 4-6-4, Character Generator Example.) The rest of the address comes from a scan counter in the DC012 control chip. The scan counter addresses the ROM according to which of the ten scans is to be displayed. The 4-bit scan counter skips over the other 6 possible addresses to the ROM, so the ROM contains data in only 10 out of 16 locations. The output of the ROM is eight bits that represent the pattern of sequential dots to be displayed for that character on that scan. The eight bits enter the video shift register, a serializer that converts the eight parallel bits into a one-bit-wide stream. An extra flip-flop stores the last bit so it can be output to the stream two or three extra times (depending on line length) to fill the intercharacter space.
Also, VT100 circuitry includes a “Dot Stretcher” to make vertical lines appear as thick as horizontal lines. If you look at page 4-76 of DEC’s VT100 Technical Manual (July 1982), you’ll see the effect of the VT100’s Dot Stretcher. Here’s how DEC illustrates it:
20 dots for 2 characters ("Ap") in 80-col mode
0 . . . . . . . . . . . . . . . . . . . .
1 . . . . 1 . . . . . . . . . . . . . . .
2 . . . 1 . 1 . . . . . . . . . . . . . .
3 . . 1 . . . 1 . . . . 1 . 1 1 1 1 . . .
4 . 1 . . . . . 1 . . . 1 1 . . . . 1 . .
5 . 1 1 1 1 1 1 1 . . . 1 1 . . . . 1 . .
6 . 1 . . . . . 1 . . . 1 . 1 1 1 1 . . .
7 . 1 . . . . . 1 . . . 1 . . . . . . . .
8 . . . . . . . . . . . 1 . . . . . . . .
9 . . . . . . . . . . . 1 . . . . . . . .
Actual characters displayed after dot stretching
0 . . . . . . . . . . . . . . . . . . . .
1 . . . . 1 1 . . . . . . . . . . . . . .
2 . . . 1 1 1 1 . . . . . . . . . . . . .
3 . . 1 1 . . 1 1 . . . 1 1 1 1 1 1 1 . .
4 . 1 1 . . . . 1 1 . . 1 1 1 . . . 1 1 .
5 . 1 1 1 1 1 1 1 1 . . 1 1 1 . . . 1 1 .
6 . 1 1 . . . . 1 1 . . 1 1 1 1 1 1 1 . .
7 . 1 1 . . . . 1 1 . . 1 1 . . . . . . .
8 . . . . . . . . . . . 1 1 . . . . . . .
9 . . . . . . . . . . . 1 1 . . . . . . .
The PCx80 Video createFontVariation() function takes both the “dot replication” and “dot stretching” features into account (along with underlining and reverse video parameters) when converting the character generator ROM data into fonts.
Disassembling the 8080 Firmware
Following in the footsteps of vt100romhax,
I disassembled the ROM, using dz80 from D52 (here’s the manual):
dz80 -80 VT100.bin
This produced VT100.d80, which I renamed to VT100.asm. I fixed one dz80 bug, replacing references to
X2000 with 2000h, and then hand-merged most of the comments from haxrom.d80.
This required some selectivity, because I didn’t want to inadvertently include any of phooky’s
screensaver-related mods to the ROM.
Finally, I verified that reassembling VT100.asm with asm8080 produced the
original VT100.bin; after adding the correct number of nop instructions to the end to the source file, the binaries matched.
The other advantage of reassembling the code is that the resulting VT100.txt makes it easy to export comments and other symbolic information to VT100.map, which can then be included in the VT100 ROM dump and passed on to the PCx80 Debugger. Here are the rebuild steps:
asm8080 -lVT100.txt VT100.asm
grep -E "[0-9]+ [0-9A-D]+.*;;" VT100.txt | sed -E "s/ *[0-9]+ ([0-9A-F]+).*;(;.*)/ \1 . \2/" > VT100.map
fileimage --file=VT100.bin --format=bytes --output=VT100.json5 --comments --overwrite
You can omit --comments from the FileImage command to reduce the size of the VT100 file.
Some VT100.asm clean-up remains, because there are still chunks of data that were incorrectly disassembled as code. From a reassembly standpoint, it doesn’t matter too much, because all the 8080 instructions unambiguously reassemble into their original binary patterns, but from a readability standpoint, it’s a nuisance.